When using a car, someone may have ignored some symptoms that they think are not serious. But these may signal that your car could be critical and need you to act as quickly as possible. And the automatic transmission valve body symptoms are not an exception.
In this post, we will discover what is a transmission valve body, an automatic transmission valve body, and the symptoms of bad valve body. Therefore, you can recognize the transmission valve body problems and fix them to maintain the best condition of your vehicle.
First of all, let’s find out what is a valve body. The valve body is the control center of the automatic transmission. It includes a maze of channels and passages that guide hydraulic fluid to the various valves.
Then they activate the appropriate clutch pack or band servo for each driving situation to switch smoothly to the appropriate gear. Like a hydraulic fluid hose, each of those channels performs, somehow, the same job.
It was much easier to mill out passages in a metal block instead of making a hundred horses run all over the place, thus keeping everything tidy as well as more reliable.
Each of the many valves has a particular role in the valve body and has a name for that feature. The most important part of the valve body is the manual valve. Connected to the gear stick handle, it instructs the right passage for hydraulic fluid to pass through.
Recently, the modern automatic transmission valve body has sensors to monitor the speed, brake pedal position, throttle position, and engine load to perform a soft and firm gear shift. The sensors send vital information to the onboard engine management computer.
It further directs the electrically controlled solenoid that redirects the hydraulic fluid to the right clutch pack. Therefore, it will ensure a soft and seamless change between gears.
Now that you know about the auto transmission valve body, it is time to know transmission valve body symptoms.
Although modern automatic gearboxes are strong and enduring, the overall reliability takes effect from the added complex structure of these systems. Therefore, the sooner we notice the abnormal signals of the engine, the longer we can maintain the use of it.
There are a few valve body transmission symptoms that keep you aware of the failure activity of the engine. Most of them are quite noticeable.
It is recommended that you should fix these problems as soon as possible. Then, your driving ability will be protected and gear changing will be smooth as usual.
Here are the automatic transmission valve body symptoms that you must not ignore
One symptom of a bad valve body is strange knocking noises. You will notice the clunking or knocking noise coming from the gearbox when you brake, change the gears, or when accelerating.
Chances are that you may hear some awkward noises when putting the car in reverse and driving backward. The reason for this can be anything from inappropriate oil pressure to actual physical damage to the transmission valve body.
Anyways, as soon as you hear strange sounds from the gearbox you should get your car a check.
Late gear shifts or general issues with gear changes are common transmission valve body symptoms. When the gearbox prepares to change gears, it will drop the RPM slightly.
A bad transmission valve body probably makes the RPM spike for a moment. Whenever you experience these problems, contact your mechanic for a check immediately
Similar to shifting gears, you might have difficulty downshifting as one of the symptoms of a bad valve body.
This explains that hydraulic fluid is unable to enter the valve body transmission properly. Once this starts happening, the gears will not function properly, thus degrading the performance of the vehicle.
Are you facing problems while changing your gears to reverse or drive? If you have ever had a long pause between going in reverse and being able to slide into drive, then you understand the pain of a delayed shift.
Most often, it is because of the transmission valve body that is working improperly. Thus, the shifting of the transmission experiences a great delay. Be ready! Due to this, it may cause the car to be stuck in neutral.
SEE MORE:
When it comes to replacing a transmission valve body, the cost is something to take into account, as it will depend on the labor and model of your vehicle.
An average transmission valve body will cost between $200 to $500. In addition, the labor costs tend to be quite intense as the process of replacing can take around 2 to 4 hours to finish.
It is important to note that the hourly rate of a mechanic costs between $60 to $100. So you will pay between $120 and $400 for labor costs before taxes and fees.
Therefore, the total valve body replacement cost will vary between $320 and $900.
If there are transmission valve body symptoms that are serious, you will need to take into consideration if you need to replace the whole valve body or fix the transmission system.
Because the cost of either replacing or fixing the automatic transmission valve body is relatively high. You should take care of the vehicle daily and keep track of the car’s condition.
The top advice to prevent transmission valve body symptoms is proper maintenance. Frequent maintenance appointments will let you know if there is any strange condition of your vehicle to fix it quickly and prevent further damage.
Also, you should use good transmission oil. Because using low-quality oils will lead to sub-par lubrication and cooling of the whole body.
Later, that will make the key components’ lifespan shorter. In terms of economics, it will be cheaper if you use good oil than to rebuild the gearbox.
Last but not least, the easiest way is to always check the warning lights on your vehicle’s dashboard. Nowadays, cars are equipped with smart and clear dashboards for you to notice any abnormal behavior inside them.
But in case you do not have them, a frequent maintenance check is always the best option to prevent transmission valve body symptoms or further damage to your car.
According to the American Automobile Association (AAA), the typical cost of a complete gearbox valve body replacement is between $300 and $1000.
In addition, if this part has any less severe issue, the typical cost to repair on most common small vehicles and sedans will be between $250 and $500.
It is rather simple to replace some valve bodies, especially when the transmission is still in the car.
To eliminate mineral build-up, gently scrape the interior walls of the valve body using a nylon bristle brush.
The best method is to disassemble everything and thoroughly clean the valves and bores using acetone and nylon brushes.
As mentioned above, the detection of a bad transmission valve body is relatively easy even with or without the help of an engine management computer. The best tip is to never ignore any unusual signs in your vehicle.
Keep up with your pages for more useful information and maintenance tips that will help you know your car better.
The valve body and its solenoids serve as the heart and brain of the automatic transmission. Why are they so important and unfortunately SO costly to repair or replace? Since the invention of the automatic transmission in 1921 and the first hydraulic transmission in 1932, manufacturers have worked to improve driver comfort, vehicle performance, and gas mileage. The latter, fuel economy, has become increasingly important in recent years due to environmental concerns. As a result, automatic transmissions have undergone great changes and have become incredibly complex systems. While older transmissions had 2, 3 or 4 speeds or “gears,” modern automatics have seen 10 speeds or more along with multiple reverse gears. Modern electronic systems monitor performance and control the transmission while driving. The valve body and solenoids play a central role in the operations of these modern transmissions, which we will look at in greater detail.
The valve body acts as the control center of the automatic transmission. Usually made of aluminum (Fun Fact: valve bodies in much older vehicles were cast iron allowing for greater durability yet the weight hindered fuel economy), it contains a maze of channels and passages that direct the transmission fluid through valves to control the various clutches, bands and drums that change gears.
Vehicles have a number of sensors that are monitoring vehicle speed, engine load and throttle position and send this information to an onboard computer, which in turn communicates with the valve body in order to shift up and down between gears. When a shift is needed, valves open and close to direct transmission fluid to the appropriate area to make the gear change occur. Transmission fluid, unlike motor oil, is more than just a lubricating fluid; it’s a hydraulic fluid. The transmission fluid flowing through the valve body is under tremendous pressure, which in turn generates heat. As the soft parts in the transmission break down, they leave small particles in the fluid as contaminants, which becomes abrasive.
This combination of pressure, heat, water intrusion and abrasion has a negative impact on the valve body over time. The valves will wear down, the channels can be abraded and become oversized, and the whole valve body unit can become warped. Signs of a bad valve body can be fluid leaks, slipping during gear changes, or even failure to go into gear.
Transmission Specifics:
Nissan has sold millions of dollars of RE5 valve bodies because of a faulty radiator. These units are found in Nissan Xterra, Nissan Pathfinder and Nissan Frontier models. A poor design causes a breach in the radiator causing coolant (glycol or radiator fluid) to sneak into the transmission coolers lines and ultimately cause water contamination in the transmission. The biggest downside to this scenario that motivated a national class action suit against Nissan is the rust that forms on the valve body that prevents the proper operations of valves. Once contaminated, there’s no turning back unless the valve body is replaced, among other items required in a quality transmission rebuild.
A solenoid is basically an electro-hydraulic switch that controls the valves in the valve body. Information from a vehicle’s computer opens and closes these switches in order to control the flow of transmission fluid and therefore the function of the transmission. Solenoids control torque converter lockup, internal transmission pressure, and shifting. As modern transmissions have become more complex, especially with electronic complexity, the number of solenoids has gone up as well. Older 4 speed transmissions may have only 2 or 3 solenoids, while some new 8 and 10 speed transmissions may have 13 or more!
Additionally, solenoids themselves have become more sophisticated. Older designs are simply binary in that they are either “on” or “off” – it’s a switch. Newer designs are often “pulse width modulated” or “variable force” solenoids. These allow the computer to adjust timing and volume of the valve opening and closing to maximize fuel efficiency and performance. Depending on manufacturer and design, these solenoids can be inside of the transmission or mounted on the outside of the housing. All in all, transmissions have become less and less dependent on mechanical and hydraulic systems and more dependent on computers and electronic controls.
Transmission specifics: Commonly found in models such as the Silverado, Suburban, Tahoe or Denali, the GM 4L60E was originally designed with a simple binary TCC (torque converter clutch) solenoid. However, the abrupt “on-off” function caused a number of premature failures in these units, leading GM to incorporate a “pulse width modulated” solenoid. This allowed a gradual lockup of the torque converter and reduced these premature failures.
The downside is that electronic components can and will fail. A solenoid can stick open or stick closed, or simply become erratic and inconsistent. When this happens, transmission problems can show up rapidly. Too much internal pressure can cause hard shifts, while too little pressure will rob the transmission of fluid causing overheating that will destroy clutch packs. A bad solenoid can cause delays in shifting, or even shifting into the wrong gear or shifting up and down unpredictably. A bad solenoid often signals an error to the computer and a “check engine” light will come on.
Transmission Specifics:
The Dodge 42RE/47RE/48RE transmission series have a history of problems with the transducer and pressure solenoids. When a solenoid is charged, it becomes magnetic. The solenoids in these Dodge transmissions are notorious for picking up metallic particles quickly and behaving erratically, causing delayed and or missed shifts. Identifying the problem and addressing it quickly can save a lot of headaches!
If your transmission’s valve body has become worn or damaged, this will usually require a proper rebuild of the transmission to repair. Occasionally this will involve simply rebuilding or replacing the valve body, but this is usually a shortcut that will lead to more problems. A bad valve body is usually a sign that there is more damage inside of the transmission, and a transmission expert needs to fully disassemble and inspect the entire transmission to ensure that everything is up to the manufacturer’s specifications. A transmission is filled with wearable components such as gaskets, seals and clutches that will deteriorate over time. Why spend money on a valve body repair when the “soft parts” have significant wear and can give out anytime?
With a bad solenoid, repairs can often be more straightforward, especially if the vehicle mileage is low and the application is not heavy duty. Assuming a solenoid failure is caught early enough, before too much damage has been done, a replacement of the bad switch can often resolve the transmission malfunction. That full rebuild for several thousand dollars that you feared might be taken care of for a few hundred dollars instead! However, it is best to have a full diagnosis performed by a transmission shop to determine the best course of action to get your vehicle up and running again. This is where an honest local transmission shop is important to program into your speed dial!
Transmission Specifics:
Dodge-Chrysler vehicles, especially Ram trucks or Jeeps, carry a 545RFE transmission that integrates its solenoids into a single block of numerous solenoids. Erratic shifting on these units is a typical problem and often can be tracked to a malfunctioning solenoid within the block. Unfortunately, these situations are not limited to high mileage situations. In low mileage situations, the solenoid block alone can be replaced saving a customer thousands of dollars required for a full transmission rebuild.
The Advanced Transmission Center team consists of technicians who have decades of experience diagnosing, rebuilding and repairing automatic transmissions in domestic and import vehicles. We have the ability to test and diagnose problems with your valve body or your transmission solenoids and use only quality parts in our repairs.
If you are having problems with your valve body, solenoids, or any transmission related issue, contact Advanced Transmission Center at either of our shop locations and we’d be happy to help! Unlike dealerships or many independent repair shops, we are transmission specialists trained to fix issues related to a vehicle drive-train. You can reach out to either location that is most convenient for you.